Skip to main content

Thread: eeePC 701SD Realtek wireless cannot connect to WEP shared key network

-

i have eeepc 701sd, wireless connected fine networks in 9.04 (including wep shared key network @ home). wireless card supported out of box r8180 driver. use normal ubuntu desktop, not unr edition.

lshw:
code:
rtl8187se wireless lan controller
however, clean 9.10 reinstall, cannot connect wep shared key network (this occured when testing beta, didnt think of , went 9.04). eeepc can connect other networks, @ university , friends place (both wpa2), issue wep shared key network. not connecting, mean put in key, set network configurations shared key, however, times out , asks key again (right after kernel problem message, see below).

have desktop running 9.10 , can connect wep shared key network no issues, , there no issues when running 9.04 either.

thus, come conclusion related change must have occured 9.04 9.10 r8180 driver eeepc. insight?

ps: aware of bug announced in release notes (i have different card, same issue). experience kernel crash if use hot key turn on/off wireless antenna. http://www.ubuntu.com/getubuntu/rele...kernel%20crash interesting thing when nm-applet times out , asks password again, red kernel crash icon pop in system tray, saying "your system encounted serious kernel problem".

cheers!

i have similar issue. upgraded 9.10 , when connected home wireless network via wep key. connects , loses connection. not issue when ran 9.04. did clean install of 9.10. oddly enough not issue if try connect unsecured network.

ideas?

btw have 1 of b43xxx wireless chip sets


Forum The Ubuntu Forum Community Ubuntu Official Flavours Support Networking & Wireless [ubuntu] eeePC 701SD Realtek wireless cannot connect to WEP shared key network


Ubuntu

Comments

Post a Comment

Popular posts from this blog

invalid use of void expresion in FlexiTimer2 library

-
Image
hello, first post asking in forum patient if dont correctly   well, im trying make robot evades obstacles , uses interrupts in order distances. ive used flexitimer2 run void function each 5ms, problem whe try verify program says me there error in use of flexitimer.    code: [select] flexitimer2::set(1, 1.0/1000, rastreodistanciamin()); i copy code below, please can tell error , how solve it, ive been loking dont know do. thank you code: [select] #include <flexitimer2.h> #include <servo.h> //motor a int ena = 7; int in1=6; int in2 = 5; //motor b int in3=11; int in4=10; int enb=9; servo cabeza; //hc-sr04 device int echo = 13; int triger = 12; //it use hc-sr04 determine , return distance in front of him int calculodistancia(){   volatile int tiempo;   volatile int distancia;   digitalwrite(triger,low); /* por cuestión de estabilización del sensor*/   delaymicroseconds(5);   digitalwrite(triger, high); /* envío del pulso ultrasónico*/   delaymicroseconds(10);   tiem
Read more

error: a function-definition is not allowed here before '{' token

-
i'm new member. me pls code: [select] void manhinh1(){                              tempc = analogread(adc);   tempc = tempc * 0.48828125;                                          lcd.setcursor(0, 0); lcd.print("nhiet: ");                                      lcd.setcursor(7, 0); lcd.print(tempc);   lcd.setcursor(13,0); lcd.print((char)223);    lcd.setcursor(14,0); lcd.print("c");   if(max > min){     if (tempc > max)            {digitalwrite(fan, low);           lcd.setcursor(2, 1); lcd.print("lam mat.....");}     else if (tempc < min)           {digitalwrite(hot, low);           lcd.setcursor(2, 1); lcd.print("dang suoi...");           delay(10000); }     else if (tempc > min && tempc < max)           {digitalwrite(fan, high);            digitalwrite(hot, high);            lcd.setcursor(2, 1); lcd.print("on dinh!!");}              }    else if (max < min){    lcd.setcursor(0, 1);               
Read more

LED Strip Code

-
i downloaded code. here have several single leds flashing music microphone. in project, instead of single rgb leds, have 5 rgb led strips. need change in code? led strip 10m supernight rgb strip cut 5 equal strips. // arduino pin numbers const int do_pin = 2; const int ao_pin = 0; int sound; int led1 = 8; int led2 = 9; int led3 = 10; int led4 = 11; int led5 = 12;   void setup() {   pinmode(do_pin, input);   pinmode(led1, output);   pinmode(led2, output);   pinmode(led3, output);   pinmode(led4, output);   pinmode(led5, output);   serial.begin(9600); }   void loop() {     if (sound > 31) {     digitalwrite(led1, high);   }     if (sound < 31) {     digitalwrite(led1, low);   }     if (sound > 35) {     digitalwrite(led2, high);   }     if (sound < 35) {     digitalwrite(led2, low);   }     if (sound > 40) {     digitalwrite(led3, high);   }     if (sound < 40) {     digitalwrite(led3, low);   }     if (sound > 45) {     digitalwrite(led4, high);   }     if
Read more