Skip to main content

Thread: Intel pro/wireless 5100 agn disabled

-

i using 9.10 , wireless disabled.
can not check wireless click on network manager.
don't know how enable it

code:
magicskyer@magicskyer-laptop:~$ sudo lshw -c network [sudo] password magicskyer:    *-network                       description: ethernet interface        product: netlink bcm5906m fast ethernet pci express        vendor: broadcom corporation        physical id: 0        bus info: pci@0000:01:00.0        logical name: eth0        version: 02        serial: 00:1f:16:0b:be:e6        size: 100mb/s        capacity: 100mb/s        width: 64 bits        clock: 33mhz        capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation        configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.99 duplex=full firmware=sb v3.04 ip=203.188.81.157 latency=0 link=yes multicast=yes port=twisted pair speed=100mb/s        resources: irq:30 memory:d5500000-d550ffff   *-network disabled        description: wireless interface        product: pro/wireless 5100 agn [shiloh] network connection        vendor: intel corporation        physical id: 0        bus info: pci@0000:02:00.0        logical name: wmaster0        version: 00        serial: 00:22:fa:7e:60:24        width: 64 bits        clock: 33mhz        capabilities: pm msi pciexpress bus_master cap_list logical ethernet physical wireless        configuration: broadcast=yes driver=iwlagn latency=0 multicast=yes wireless=ieee 802.11abgn        resources: irq:29 memory:d4500000-d4501fff

is there can me solve problem?


Forum The Ubuntu Forum Community Ubuntu Official Flavours Support Networking & Wireless [ubuntu] Intel pro/wireless 5100 agn disabled


Ubuntu

Comments

Post a Comment

Popular posts from this blog

invalid use of void expresion in FlexiTimer2 library

-
Image
hello, first post asking in forum patient if dont correctly   well, im trying make robot evades obstacles , uses interrupts in order distances. ive used flexitimer2 run void function each 5ms, problem whe try verify program says me there error in use of flexitimer.    code: [select] flexitimer2::set(1, 1.0/1000, rastreodistanciamin()); i copy code below, please can tell error , how solve it, ive been loking dont know do. thank you code: [select] #include <flexitimer2.h> #include <servo.h> //motor a int ena = 7; int in1=6; int in2 = 5; //motor b int in3=11; int in4=10; int enb=9; servo cabeza; //hc-sr04 device int echo = 13; int triger = 12; //it use hc-sr04 determine , return distance in front of him int calculodistancia(){   volatile int tiempo;   volatile int distancia;   digitalwrite(triger,low); /* por cuestión de estabilización del sensor*/   delaymicroseconds(5);   digitalwrite(triger, high); /* envío del pulso ultrasónico*/   delaymicroseconds(10);   tiem
Read more

error: a function-definition is not allowed here before '{' token

-
i'm new member. me pls code: [select] void manhinh1(){                              tempc = analogread(adc);   tempc = tempc * 0.48828125;                                          lcd.setcursor(0, 0); lcd.print("nhiet: ");                                      lcd.setcursor(7, 0); lcd.print(tempc);   lcd.setcursor(13,0); lcd.print((char)223);    lcd.setcursor(14,0); lcd.print("c");   if(max > min){     if (tempc > max)            {digitalwrite(fan, low);           lcd.setcursor(2, 1); lcd.print("lam mat.....");}     else if (tempc < min)           {digitalwrite(hot, low);           lcd.setcursor(2, 1); lcd.print("dang suoi...");           delay(10000); }     else if (tempc > min && tempc < max)           {digitalwrite(fan, high);            digitalwrite(hot, high);            lcd.setcursor(2, 1); lcd.print("on dinh!!");}              }    else if (max < min){    lcd.setcursor(0, 1);               
Read more

LED Strip Code

-
i downloaded code. here have several single leds flashing music microphone. in project, instead of single rgb leds, have 5 rgb led strips. need change in code? led strip 10m supernight rgb strip cut 5 equal strips. // arduino pin numbers const int do_pin = 2; const int ao_pin = 0; int sound; int led1 = 8; int led2 = 9; int led3 = 10; int led4 = 11; int led5 = 12;   void setup() {   pinmode(do_pin, input);   pinmode(led1, output);   pinmode(led2, output);   pinmode(led3, output);   pinmode(led4, output);   pinmode(led5, output);   serial.begin(9600); }   void loop() {     if (sound > 31) {     digitalwrite(led1, high);   }     if (sound < 31) {     digitalwrite(led1, low);   }     if (sound > 35) {     digitalwrite(led2, high);   }     if (sound < 35) {     digitalwrite(led2, low);   }     if (sound > 40) {     digitalwrite(led3, high);   }     if (sound < 40) {     digitalwrite(led3, low);   }     if (sound > 45) {     digitalwrite(led4, high);   }     if
Read more