9v 2.2A external power for uno and servo NEED HELP

-

hi, i'm new arduino , knowledge in electronic component basic. i'll try write more infos can on project, question powering:

this setup:

- uno board r3 (maybe nano final assembling)
- servo motor (a big one) rds3109mg
- 433mz receiver (to receive wireless command servo)
- push button (to manually command servo)

right testing, uno board connected via usb , servo/433mhz receiver powered via breadboard adapter 9v 1000ma. work ok. (uno , breadboard grounded together). if connect uno board breadboard 9v adapter vin pin, uno reset when activating servo, not enough power.

i'm ready move next stage make pcb. need on how powering stuff.

i have prefer battery pack don't need hide wire concern life time of battery. (it automatic blind closing system servo open , close blind lot of time).

i red lot of topic telling better have 1amp servo (project have 2 servo in future).

my major question is: can plug 9v 2.2a (2200ma) adapter directly in uno board? there amp limit board ?

if can, think there enough amp plug servo directly on 5v pin without lack of power board causing it's own reset?

thank lot in advance able me

quote
my major question is: can plug 9v 2.2a (2200ma) adapter directly in uno board? there amp limit board ?
you should able connect 9v battery uno external power barrel jack. should not power servo arduino power capacity limited. if servo 6v servo, ubec ebay power 9v battery.


Arduino Forum > Using Arduino > Motors, Mechanics, and Power (Moderator: fabioc84) > 9v 2.2A external power for uno and servo NEED HELP


arduino

Comments

Post a Comment

Popular posts from this blog

invalid use of void expresion in FlexiTimer2 library

-
Image
hello, first post asking in forum patient if dont correctly   well, im trying make robot evades obstacles , uses interrupts in order distances. ive used flexitimer2 run void function each 5ms, problem whe try verify program says me there error in use of flexitimer.    code: [select] flexitimer2::set(1, 1.0/1000, rastreodistanciamin()); i copy code below, please can tell error , how solve it, ive been loking dont know do. thank you code: [select] #include <flexitimer2.h> #include <servo.h> //motor a int ena = 7; int in1=6; int in2 = 5; //motor b int in3=11; int in4=10; int enb=9; servo cabeza; //hc-sr04 device int echo = 13; int triger = 12; //it use hc-sr04 determine , return distance in front of him int calculodistancia(){   volatile int tiempo;   volatile int distancia;   digitalwrite(triger,low); /* por cuestión de estabilización del sensor*/   delaymicroseconds(5);   digitalwrite(triger, high); /* envío del pulso ultrasónico*/   delaymicroseconds(10);   tiem
Read more

error: a function-definition is not allowed here before '{' token

-
i'm new member. me pls code: [select] void manhinh1(){                              tempc = analogread(adc);   tempc = tempc * 0.48828125;                                          lcd.setcursor(0, 0); lcd.print("nhiet: ");                                      lcd.setcursor(7, 0); lcd.print(tempc);   lcd.setcursor(13,0); lcd.print((char)223);    lcd.setcursor(14,0); lcd.print("c");   if(max > min){     if (tempc > max)            {digitalwrite(fan, low);           lcd.setcursor(2, 1); lcd.print("lam mat.....");}     else if (tempc < min)           {digitalwrite(hot, low);           lcd.setcursor(2, 1); lcd.print("dang suoi...");           delay(10000); }     else if (tempc > min && tempc < max)           {digitalwrite(fan, high);            digitalwrite(hot, high);            lcd.setcursor(2, 1); lcd.print("on dinh!!");}              }    else if (max < min){    lcd.setcursor(0, 1);               
Read more

LED Strip Code

-
i downloaded code. here have several single leds flashing music microphone. in project, instead of single rgb leds, have 5 rgb led strips. need change in code? led strip 10m supernight rgb strip cut 5 equal strips. // arduino pin numbers const int do_pin = 2; const int ao_pin = 0; int sound; int led1 = 8; int led2 = 9; int led3 = 10; int led4 = 11; int led5 = 12;   void setup() {   pinmode(do_pin, input);   pinmode(led1, output);   pinmode(led2, output);   pinmode(led3, output);   pinmode(led4, output);   pinmode(led5, output);   serial.begin(9600); }   void loop() {     if (sound > 31) {     digitalwrite(led1, high);   }     if (sound < 31) {     digitalwrite(led1, low);   }     if (sound > 35) {     digitalwrite(led2, high);   }     if (sound < 35) {     digitalwrite(led2, low);   }     if (sound > 40) {     digitalwrite(led3, high);   }     if (sound < 40) {     digitalwrite(led3, low);   }     if (sound > 45) {     digitalwrite(led4, high);   }     if
Read more