SMS & Call controlled I/O, Easy for some! - Raspberry Pi Forums

-

hi there,

new , green toward gear most, drawn toward technology because never had when younger! interest in raspberry pi leaning toward necessity company deal consumer ripping me off blind!

project involves assembling little board suitable 3g modem option capable of talking australian gsm networks.

need "device" have 4 x output contacts (n/o-c-n/c)
1 of 4 outs driven incoming call can latch or pulse depending on user setup. (c.l.i dependent via user list of numbers)
balance 3 of 4 outs sms driven "#on & #off command"
outputs remember last state after power cycle.

4 x inputs (v/free) capable of triggering message either open/closed state. (1 input = 2 x messages@ 32 characters each & user programmable)

inputs trigger instant messaging per state of each input maximum of 4 users per input. users contained in user c.l.i list. 100 potential users call in (out1 relay) operation.

device run on 8 - 32 volts dc plus have backup battery if supply off momentary. backup charged via input dc supply?

6 x indication leds
green = power
tri led (red=no network/yellow=modem busy/green=ready standby)
4 x red per relay status

firstly, appreciate can or assist information or direction toward dilemma, secondly, thank in advance showing patience! appreciate this. no.... cant write code, i'm finding hard navigating forum let alone understanding 2% of whats being discussed, know want , if 1 person replies, better none!

if can assist me in understanding product , need use in order achieve above, helpful me , others... appreciate anyone's assistance!

thank much

david



raspberrypi



Comments

Post a Comment

Popular posts from this blog

invalid use of void expresion in FlexiTimer2 library

-
Image
hello, first post asking in forum patient if dont correctly   well, im trying make robot evades obstacles , uses interrupts in order distances. ive used flexitimer2 run void function each 5ms, problem whe try verify program says me there error in use of flexitimer.    code: [select] flexitimer2::set(1, 1.0/1000, rastreodistanciamin()); i copy code below, please can tell error , how solve it, ive been loking dont know do. thank you code: [select] #include <flexitimer2.h> #include <servo.h> //motor a int ena = 7; int in1=6; int in2 = 5; //motor b int in3=11; int in4=10; int enb=9; servo cabeza; //hc-sr04 device int echo = 13; int triger = 12; //it use hc-sr04 determine , return distance in front of him int calculodistancia(){   volatile int tiempo;   volatile int distancia;   digitalwrite(triger,low); /* por cuestión de estabilización del sensor*/   delaymicroseconds(5);   digitalwrite(triger, high); /* envío del pulso ultrasónico*/   delaymicroseconds(10);   tiem
Read more

error: a function-definition is not allowed here before '{' token

-
i'm new member. me pls code: [select] void manhinh1(){                              tempc = analogread(adc);   tempc = tempc * 0.48828125;                                          lcd.setcursor(0, 0); lcd.print("nhiet: ");                                      lcd.setcursor(7, 0); lcd.print(tempc);   lcd.setcursor(13,0); lcd.print((char)223);    lcd.setcursor(14,0); lcd.print("c");   if(max > min){     if (tempc > max)            {digitalwrite(fan, low);           lcd.setcursor(2, 1); lcd.print("lam mat.....");}     else if (tempc < min)           {digitalwrite(hot, low);           lcd.setcursor(2, 1); lcd.print("dang suoi...");           delay(10000); }     else if (tempc > min && tempc < max)           {digitalwrite(fan, high);            digitalwrite(hot, high);            lcd.setcursor(2, 1); lcd.print("on dinh!!");}              }    else if (max < min){    lcd.setcursor(0, 1);               
Read more

LED Strip Code

-
i downloaded code. here have several single leds flashing music microphone. in project, instead of single rgb leds, have 5 rgb led strips. need change in code? led strip 10m supernight rgb strip cut 5 equal strips. // arduino pin numbers const int do_pin = 2; const int ao_pin = 0; int sound; int led1 = 8; int led2 = 9; int led3 = 10; int led4 = 11; int led5 = 12;   void setup() {   pinmode(do_pin, input);   pinmode(led1, output);   pinmode(led2, output);   pinmode(led3, output);   pinmode(led4, output);   pinmode(led5, output);   serial.begin(9600); }   void loop() {     if (sound > 31) {     digitalwrite(led1, high);   }     if (sound < 31) {     digitalwrite(led1, low);   }     if (sound > 35) {     digitalwrite(led2, high);   }     if (sound < 35) {     digitalwrite(led2, low);   }     if (sound > 40) {     digitalwrite(led3, high);   }     if (sound < 40) {     digitalwrite(led3, low);   }     if (sound > 45) {     digitalwrite(led4, high);   }     if
Read more