wiring of ILI9225 display plus SD slot ?

-

hello,
how have wire ili9225 display
http://www.ebay.de/itm/201042408158?_trksid=p2059210.m2749.l2649&sspagename=
to arduino mega pins if wish use spi both tft , sd slot?

standard tft breakout pin
7. clk surely 52,
8. sdi supposed mosi (51),

but arduino pins connected standard
6. led,
9. rs,
10. rst,
11. cs... ?


and following 2 expand pins wired:
1. sd_cs--sd cars chip selection pin
5. f_cs-- spi flash signal

quote
code: [select]
11pin standard wiring used io:

1. vcc--power supply (5v/3.3v)
2. gnd-- power supply (gnd)
3. gnd-- power supply (gnd)
4. nc--no connect
5. nc--no connect
6. led-- pick io control light off or pwm brightness control
7. clk--spi clock signal
8. sdi--serial data input pin
9. rs--command (rs=0)/ parameter (rs=1)
10. rst--reset pin
11. cs-- chip selection pin


5 pin expand wiring used io:

1. sd_cs--sd cars chip selection pin
2. sd_mosi--mosi input
3. sd_miso--miso output
4. sd_sck-- spi clock signal
5. f_cs-- spi flash signal
thanks in advance!

hi there...i need help...i sorry iam new forum posting qustion on wrong place gor ask anyway...so question possible have 1.44" tft lcd + touch( adafruit 1.44" color tft lcd display microsd card breakout - st7735r) ...link this: http://www.adafruit.com/products/2088  ????


Arduino Forum > Using Arduino > Displays > wiring of ILI9225 display plus SD slot ?


arduino

Comments

Post a Comment

Popular posts from this blog

invalid use of void expresion in FlexiTimer2 library

-
Image
hello, first post asking in forum patient if dont correctly   well, im trying make robot evades obstacles , uses interrupts in order distances. ive used flexitimer2 run void function each 5ms, problem whe try verify program says me there error in use of flexitimer.    code: [select] flexitimer2::set(1, 1.0/1000, rastreodistanciamin()); i copy code below, please can tell error , how solve it, ive been loking dont know do. thank you code: [select] #include <flexitimer2.h> #include <servo.h> //motor a int ena = 7; int in1=6; int in2 = 5; //motor b int in3=11; int in4=10; int enb=9; servo cabeza; //hc-sr04 device int echo = 13; int triger = 12; //it use hc-sr04 determine , return distance in front of him int calculodistancia(){   volatile int tiempo;   volatile int distancia;   digitalwrite(triger,low); /* por cuestión de estabilización del sensor*/   delaymicroseconds(5);   digitalwrite(triger, high); /* envío del pulso ultrasónico*/   delaymicroseconds(10);   tiem
Read more

error: a function-definition is not allowed here before '{' token

-
i'm new member. me pls code: [select] void manhinh1(){                              tempc = analogread(adc);   tempc = tempc * 0.48828125;                                          lcd.setcursor(0, 0); lcd.print("nhiet: ");                                      lcd.setcursor(7, 0); lcd.print(tempc);   lcd.setcursor(13,0); lcd.print((char)223);    lcd.setcursor(14,0); lcd.print("c");   if(max > min){     if (tempc > max)            {digitalwrite(fan, low);           lcd.setcursor(2, 1); lcd.print("lam mat.....");}     else if (tempc < min)           {digitalwrite(hot, low);           lcd.setcursor(2, 1); lcd.print("dang suoi...");           delay(10000); }     else if (tempc > min && tempc < max)           {digitalwrite(fan, high);            digitalwrite(hot, high);            lcd.setcursor(2, 1); lcd.print("on dinh!!");}              }    else if (max < min){    lcd.setcursor(0, 1);               
Read more

LED Strip Code

-
i downloaded code. here have several single leds flashing music microphone. in project, instead of single rgb leds, have 5 rgb led strips. need change in code? led strip 10m supernight rgb strip cut 5 equal strips. // arduino pin numbers const int do_pin = 2; const int ao_pin = 0; int sound; int led1 = 8; int led2 = 9; int led3 = 10; int led4 = 11; int led5 = 12;   void setup() {   pinmode(do_pin, input);   pinmode(led1, output);   pinmode(led2, output);   pinmode(led3, output);   pinmode(led4, output);   pinmode(led5, output);   serial.begin(9600); }   void loop() {     if (sound > 31) {     digitalwrite(led1, high);   }     if (sound < 31) {     digitalwrite(led1, low);   }     if (sound > 35) {     digitalwrite(led2, high);   }     if (sound < 35) {     digitalwrite(led2, low);   }     if (sound > 40) {     digitalwrite(led3, high);   }     if (sound < 40) {     digitalwrite(led3, low);   }     if (sound > 45) {     digitalwrite(led4, high);   }     if
Read more